Infinite bracelet

Bracelet made from the PRECIOSA Ripple™ pressed bead

This simple tutorial will enable you to produce your own original accessory. The new PRECIOSA Ripple™ pressed beads can be used in many different ways and this tutorial will give you with the opportunity to try out one of them.


icon pdf downloadInfinite Bracelet


PRECIOSA ORNELA presents the new PRECIOSA Ripple™ pressed bead from the PRECIOSA Traditional Czech Beads brand. This round bead with a diameter of 12 mm has a centrally located hole and an identical undulating surface on both sides. The symmetrical profile on both sides of the bead enables its 100% use during the application of a series of ten new types of combined, dual color vacuum decorations known as California. The bead's undulating surface can also be enlivened with metallic decorations in a glossy and mat finish. The centrally located hole in this bead means that it is excellent for combining with seed beads or with small fire polished beads during stringing and embroidering.

Make a beautiful, but simple accessory. Try and see what can be achieved using the new PRECIOSA Ripple™ pressed bead. The simple combination of this pressed bead with rocailles can make even the simplest piece of jewelry enchanting. Thanks to the range of colors and surface finishes on the beads and seed beads from the PRECIOSA Traditional Czech Beads brand, you are sure to be able to find the color scheme you require, either using tone in tone or color contrasts. It is entirely up to you. The organic shape of the PRECIOSA Ripple™ bead in this combination gives the impression that it has been conjured up by nature.

We wish you much enjoyment and many new ideas when working with beads and seed beads from the PRECIOSA Traditional Czech Beads brand.

 

 

Materials and tools:

PRECIOSA Ripple™ pressed beads (Rip)

111 01 351; 12 mm; a mixture of colors (about 35 – 50x depending on the length of the bracelet, 10x for the earrings)

nekonecny naramek 1a

PRECIOSA rocailles (R10, R6)

311 19 001 or 331 19 001 or 331 29 001; 10/0, 6/0; the color of your choice

nekonecny naramek 2a

a 0.20 mm or 0.3 mm nylon line; a thin needle; scissors; flat nose pliers (for flattening the end of the line prior to stringing)

Earring hooks; needle nose pliers; 8 mm rings

 

Procedure:

The bracelet without a fastening

Step 1:

String the bracelet on the doubled 0.2 mm line. The length of the line is twice the span of the hand. Thread the needle and move it to the middle of the line. Tie a knot at the end of the line. This should prevent the rocailles from coming off the stringing.

 

Step 2:

Prepare 180 to 280 R10 depending on the required length of the bracelet. String 4x R10 between the two neighboring Rip. Add 1x R10 above the opening from the face side of the Rip. String 4x R10, 1x Rip and 1x R10 and return to the Rip. String a further 4x R10, 1x Rip and 1x R10 and return to the Rip.

nekonecny naramek 2b

Step 3:

Continue in the same way up to the end of the bracelet. Cut off the end knots on the line. Tie the 2 ends of the line together using two knots. Pull them into the surrounding rocailles between the Rip. Cut off any excess line.

 

Step 4:

Adjust the length of the bracelet so that it can be pulled onto the wrist across the palm. The bracelet will flex. It will adjust itself to the size of the wrist.

You can also string the bracelet on stretch cord or elastic (a flexible line).

nekonecny naramek 4a

The bracelet with a fastening

Step 1:

Prepare 50x Rip, 100x R6 and 75x R10. String the bracelet onto the thicker 0.3 mm line. The necessary length of the line is measured according to the span of the hand. Flatten the ends of the line with the flat nose pliers and thread it onto the thin stringing needle. Do not cut the line off the bobbin. Always keep the stringing well tightened.

 

Step 2:

String 1x R6, 1x Rip and 1x R10 and then thread the needle and the line back through the central hole of the Rip and the nearest R6. String 2x R6, 1x Rip and 1x R10 and then thread the needle and the line back through the central hole of the Rip and the nearest R6. Continue in this way to the end of the bracelet. String 1x R6, 1x Rip and 1x R10 in front of the last Rip and then thread the needle and the line back through the central hole of the Rip and the nearest R6. Tighten the stringing again.

nekonecny naramek 2c

Step 3:

String 2x R6 and 25x R10 and then thread the needle and the line back through the nearest R6. Catch the line between the next nearest R6 and then thread the line through the created R10 loop once again and thread the needle and the line through two R6. Tighten the stringing, sew the line in and cut it off.

nekonecny naramek 3

Step 4:

Tighten the second end of the bracelet, secure the line between the rocailles with knots and cut it from the bobbin.

nekonecny naramek 4b

The earrings

Step 1:

Prepare 20x Rip, 40x R6 and 20x R10 for 1 pair of earrings. String the earrings onto the thicker 0.3 mm line: you will need ca 50 cm. Flatten the end of the line with the flat nose pliers and thread it through the eye of the thin stringing needle. Do not cut the line from the bobbin. Always keep the stringing well tightened.

 

Step 2:

String 2x R6, 1x Rip and 1x R10 and then thread the needle and the line back through the central hole of the Rip and the nearest R6. Continue in this way until the end of the stringing. Connect the ends of the line using two to three strong knots and then sew it in and cut it off.

 

Step 3:

String the earring hook on the ring and connect it to the created earring. Create the second earring in the same way.

nekonecny naramek 3bnekonecny naramek 3a

nekonecny naramek 6

nekonecny naramek 5

Designers: Helena Chmelíková, Jaroslava Růžičková

This website is using cookies

To improve our services and provide information that suits your interest, we use the advanced website traffic analytics tools. However, we need your consent. More information about how we process and protect your data can be found in the privacy statement. We ask you for approval of the terms.

Functional cookies These cookies are necessary for the proper functioning of the website and therefore cannot be turned off.
Analytics cookies Analytical cookies help us track and analyze the way visitors interact with our site in Google Analytics 4. This information allows us to improve content and provide a better user experience.
Marketing cookies Reading and writing cookies for marketing purposes for advertising systems such as Google Ads or Sklik. These cookies allow us to track user behavior and measure website performance and the effectiveness of our advertising campaigns.
Personalized advertising Remarketing cookies allow us to present you with personalized advertising based on your previous interactions with our site in systems such as Google Ads, Sklik.
Use of personal data With this option, you consent to the sending and processing of your personal data to Google for the purposes of targeting and evaluating online advertising and targeted marketing.